BOLD MAGENTA part numbers are new for 2027 DRIVETRAIN PARTS-UNLIMITED.COM SNOW | 2027 DRIVETRAIN 443 TRACK SPROCKETS SPECIFICATIONS POSITION TEETH PITCH PART # Rear (black, for shaft w/ welded flanges) 9 1.97” 1241-0027 TRACK SPROCKET APPLICATIONS FITS MODEL INNER PART # MOTO-SKI Mirage 79 1241-0027 Nuvik 76-77 1241-0027 Spirit 250 76-83 1241-0027 SKI-DOO All models 60-64 1241-0027 FITS MODEL INNER PART # SKI-DOO (CONT) Alpine 68-87 1241-0027 Blizzard (all) 70-71 1241-0027 Chalet 65-67 1241-0027 Citation 300 78-79 1241-0027 Elan 71-96 1241-0027 FITS MODEL INNER PART # SKI-DOO (CONT) Elite 73-74 - Nordic 69-71 1241-0027 Olympique 65-78 1241-0027 Skandic 70-71 1241-0027 Super Olympique 68 1241-0027 FITS MODEL INNER PART # SKI-DOO (CONT) TNT (all) 69-71 - TNT 340 F/A 74 - TNT 400/440 F/A 74 1241-0027 Valmont 71-73 1241-0027 1241-0027 DESCRIPTION PART # Rubber bogie tire BT-001 RUBBER BOGIE TIRE •Black rubber bogie tire fits all Ski-Doo models with bogie suspension ANTI-STAB WHEEL KITS •Use to keep the track from contacting rail tips •Available in two styles: centered or split •Centered kits are for suspensions with offset or dual limiter straps •Split wheel kits are for suspensions with centered limiter straps DESCRIPTION STYLE PART # 8 3/4” shaft for Arctic Cat and Yamaha models Centered 4702-0073 8 5/8” shaft for Polaris and Ski-Doo models Split 4702-0074 4702-0073 4702-0074 FITS MODEL PITCH SIZE TOOTH SIZE HEX DRIVE SHAFT SIZE PART # ARCTIC CAT All models (except any with Diamond Drive, King Cat 04, Mountain Cat 800/900 03-04) 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 POLARIS All models (except Edge, Fusion and IQ 06-11) 2.52” 8 1” hex 1241-0005 2.52” 9 1” hex 1241-0008 Edge 00-08 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 SKI-DOO All ZX/REV chassis 98-07 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 YAMAHA Phazer 84-89 2.52” 8 1” hex 1241-0005 2.52” 9 1” hex 1241-0008 FITS MODEL PITCH SIZE TOOTH SIZE HEX DRIVE SHAFT SIZE PART # YAMAHA (CONT) Exciter 87-93 2.52” 8 1” hex 1241-0005 2.52” 9 1” hex 1241-0008 Vmax 500/600 94 2.52” 8 1” hex 1241-0005 2.52” 9 1” hex 1241-0008 Vmax 500 95-03 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 Vmax 4 750 92-97 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 Apex (all) (except 09 Apex) 2.52” 8 1 1/16” to 1 1/8” hex 1241-0006 2.86” 8 1 1/16” to 1 1/8” hex 1241-0019 2.52” 9 1 1/16” to 1 1/8” hex 1241-0009 NO-SLIP DRIVE SPROCKETS™ •Built to drive off of four track lugs and track clips at the same time • Specifically for full-windowed track only, designed for less rotating mass •Extra involutes are eliminated with these sprockets • Available in 2.52” and 2.86” pitch •Available in 8- or 9-tooth sprockets •Sold in pairs NOTE: Some models will require the front of the slide rails to be shortened for clearance. It is recommended that the skid frame be installed without the springs and cycled to check rail tip clearance. by •It is necessary to install an anti-stab wheel kit when shortening the suspension rail or removing the rail tip protectors •Installation instructions are included NOTE: It is recommended to use thread lock when installing bolts.
RkJQdWJsaXNoZXIy