dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 858 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0932-0266 For 17-23 M-Eight water-cooled Touring 0932-0267 For 17-23 M-Eight oil-cooled OIL PUMPS FOR M-EIGHT •PART # 0932-0267 features 20% flow increase on supply side and 52% flow increase on scavenge •PART # 0932-0266 features 44% increase on the supply side and 58% flow increase on scavenge •Pumps are made from precision-machined billet aluminum •Independent scavenge sections for flywheel cavity and cam chest •Debris screen in both scavenge pickups •Magnet in the cam chest helps prevent debris from entering the pump •Increased flow capacity on both feed and scavenge side •Adjustable pressure relief valve can be adjusted with unit in engine •Blue anodized finish •Made in the U.S.A. PART # DESCRIPTION 0932-01061 For 07-17 Twin Cam and 06 Dyna 1 Will not fit 00-02 Softails when used with a TC3 cam plate. TC3 OIL PUMP •Three stages for consistent pressure and reliable scavenging •Separate scavenge sections for flywheel cavity and cam chest (no interface) •Screens and magnetic traps help protect the scavenge rotors from debris •Special design allows S&S pump to tolerate more pinion shaft run-out without damage •Made in the U.S.A. PART # DESCRIPTION 0932-0236 For 17-24 M-Eight air/oil-cooled motors (includes an oil pump-to-case seal) 0932-0304 For 17-24 M-Eight air/oil-cooled motors (uses OEM seal) HIGH-PERFORMANCE M-EIGHT OIL PUMPS •126% feed and 131% scavenge volume compared to OEM (stock) M8 fourth generation oil pumps at 1000 rpm •123% feed and 146% scavenge volume compared to OEM (stock) M8 fourth generation oil pumps at 2500 rpm •Scavenge side discharge was improved by modifying the suction ratio to help eliminate sumping from excess oil in the crankcase •Improved oil flow by inserting an oil passage correction spacer between the large-capacity oil pump body and the cam support plate PART # DESCRIPTION 0932-0088 For 07-17 Twin Cam and 06 Dyna 0932-0087 For all 99-06 Twin Cam (except 06 Dyna) REPLACEMENT COMPONENTS 0932-0219 Gerotor scavenge for Twin Cam 88” and 96” applications 0932-0220 Gerotor feed for Twin Cam 88” and 96” applications 0932-0221 Partition plate and O-ring set for 88” Twin Cam applications 0932-0222 Partition plate and O-ring set for 96” Twin Cam applications HIGH-PERFORMANCE TWIN CAM OIL PUMPS •Helps to reduce oil carryover during high rpm operation; higher volume helps reduce engine and oil temperatures •53 mm diameter rotors for maximum performance •Gain of 20% oil pressure, 125% pressure volume and 135% scavenge volume over OEM stock TC88 oil pumps •Gain of 16% oil pressure, 66% pressure volume and 100% scavenge volume over OEM stock TC96/103 oil pumps •High-quality die-cast aluminum body construction, high-strength steel gear construction •Fits both stock and aftermarket cam support plates for seamless installation NOTE: Does not fit Screamin’ Eagle cam plate. PART # DESCRIPTION 0932-0189 For 91-22 XL (except RH Sportster) OIL PUMP ASSEMBLY •High-quality replacement cast aluminum pump body with steel gears and shaft •Raw cast-aluminum finish •Gaskets and seals included 0932-0236 0932-0088 0932-0221 0932-0219 0932-0266
RkJQdWJsaXNoZXIy OTcxOTk3