dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 834 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. XL AND BUELL CAMS •Cams run to 6500 rpm with stock hydraulic lifters; recommend solids not be installed •Stock base circle sizes allow the use of stock pushrods •V2 and N2 are bolt-in cams for stock applications designed for up to 6000 rpm •N3 cams are bolt-in for 05-16 883/1200 engines with stock springs and heads (cams for 04-06 models with more than 0.465” lift may need different valves, springs and collars) •V4 and N4 are for stock or modified applications and have a slightly higher idle speed, but can be used with stock hydraulic lifters and springs; rpm range of 2500 to 6500 •V6 and N6 designed for modified 1200s to 80” and/or high-compression pistons: stock springs and hydraulic lifters recommended; rpm range 2500 to 6500 •V8 and N8 designed for modified 883, 1100 and 1200 stroker models; stock springs and hydraulic lifters recommended; rpm range 2000 to 6000 •Made in the U.S.A. DS-199076 DS-199111 GRIND OPEN CLOSE DURATION @ 0.053” VALVE LIFT LIFT @ TDC V2, N2 Intake 22° 38° 240° 0.465” 0.180” Exhaust 46° 18° 244° 0.440” 0.155” N3 Intake 17° 33° 240° 0.465” 0.181” Exhaust 43° 11° 234° 0.482” 0.134” V4, N4 Intake 30° 46° 256° 0.490” 0.216” GRIND OPEN CLOSE DURATION @ 0.053” VALVE LIFT LIFT @ TDC V4, N4 (CONT) Exhaust 52° 24° 256° 0.490” 0.198” V6, N6 Intake 34° 50° 264° 0.500” 0.241” Exhaust 56° 28° 264° 0.500” 0.212” V8, N8 Intake 32° 44° 256° 0.490” 0.226” Exhaust 56° 28° 264° 0.500” 0.212” FOR 86-90 XL PART # DESCRIPTION EMIS* DS-199295 V2 cams 3 PART # DESCRIPTION EMIS* DS-199296 V4 cams 3 PART # DESCRIPTION EMIS* DS-199111 V8 cams 3 FOR 91-99 XL AND 94-99 BUELL PART # DESCRIPTION EMIS* DS-199195 N2 cams 3 PART # DESCRIPTION EMIS* DS-199196 N4 cams 3 PART # DESCRIPTION EMIS* DS-199114 N6 cams 3 FOR 00-22 XL (EXCEPT RH SPORTSTER) AND 00-02 BUELL PART # DESCRIPTION EMIS* DS-199075 N2 cams 3 0925-0072 N3 cams (05-17 XL only) 3 PART # DESCRIPTION EMIS* DS-199076 N4 cams 3 DS-199077 N6 cams 3 PART # DESCRIPTION EMIS* DS-199078 N8 cams 3
RkJQdWJsaXNoZXIy OTcxOTk3