dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 804 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0929-0085 For 17-23 M-Eight, 99-17 Twin Cam, 00-22 XL (except RH Sportster) PRECISION TAPPETS •All-new improved design •Hand-assembled to exact tolerances •Reduced valve train noise from startup to shutdown •Close tolerances for low leak-down rates •Fast pump-up and superior high rpm performance •Replace standard and premium lifters •Sold as a set of four •Made in the U.S.A. PART # DESCRIPTION FOR 86-90 XL 0929-0061 W/ HL2T kit PART # DESCRIPTION FOR 86-90 XL (CONT) 0929-0004 W/o HL2T kit HYDRAULIC TAPPETS •Rollers have a larger-than-stock inner bearing race that reduces stress and increases axle life •Each lifter body and plunger assembly is hand-fit and pressure-tested to ensure correct operation •Redesigned plunger assembly withstands forces associated with heavy-duty valve springs and pushrods typically used in high-performance applications •Revised metering device precisely controls oil delivery to top end, ensuring rapid lifter pump-up and reducing possibility of oil starvation to bottom end •Tappets that include the HL2T Limited Travel Kit improve cold starts and high-rpm valve timing accuracy •Sold in sets of four 0929-0004 PART # DESCRIPTION FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-22 XL (EXCEPT RH SPORTSTER), 09-12 XR1200 AND 00-09 BUELL 0929-0046 Standard PART # DESCRIPTION FOR 86-90 XL AND 87-90 BUELL 0929-0043 Standard 0929-0044 +0.002” oversize POWERGLIDE™ STEADY ROLL TAPPETS •The same Powerglide advantage (oil-fed axle, billet steel body, precision fit hydraulics) but now incorporates a Steady Roll bronze bushing in place of the needle bearing roller •These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities •Billet body •Increased roller width •Roller perpendicularity held to 0.0002” •Hand-honed hydraulic unit cavity •Dynamic load capacities increased over 30% •Lubrication capacities for hydraulic unit and valve train (top end) increased 10% •Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling •Sold each •Made in the U.S.A. 0929-0043 0929-0046 PART # DESCRIPTION FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-21 XL/XR1200 (EXCEPT RH SPORTSTER) AND 00-09 BUELL 0929-0014 Standard PART # DESCRIPTION FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-21 XL/XR1200 (EXCEPT RH SPORTSTER) AND 00-09 BUELL (CONT) 0929-0023 +0.005” oversize POWERGLIDE II HYDRAULIC TAPPETS •These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities •Billet body •Increased roller width •Roller perpendicularity held to 0.0002” •Hand-honed hydraulic unit cavity •Dynamic load capacities increased over 30% •Lubrication capacities for hydraulic unit and valve train (top end) increased 10% •Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling •Sold each •Made in the U.S.A. 0929-0014
RkJQdWJsaXNoZXIy OTcxOTk3