dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 790 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION FOR 05-17 88”/96”/103” TWIN CAM, 04-22 XL (EXCEPT RH SPORTSTER), 09-12 XR1200 0926-0854 7°, 7 mm valve stem with stock triple keeper groove FOR 99-04 TWIN CAM AND 86-03 XL 0926-0853 10°, standard 5/16” valve stem and keeper groove FOR TWIN CAM W/ SCREAMIN’ EAGLE HEADS 0926-1469 5/16” valve stem and keeper groove and 0.530” diameter valve guides HIGH-LOAD BEEHIVE® VALVE SPRINGS WITH TITANIUM RETAINERS •Made from premium stress-relieved conical ovate wire with nitrided surface heat treatment, shot-peened surface enhancements and Nano Peen™ polish •Feature extremely high level of fatigue life •Use a much smaller and lighter weight retainer to reduce valve weight and create quicker rev and smoother motion •Designed to handle the highest demands of performance engines with high-lift, steep-ramped camshafts •Allow up to 0.750” lift cams; no rocker box clearancing required •Available for 5/16” and 7 mm valves •Kits include: High-Load BeeHive® valve springs, lightweight 10° Titanium retainers manufactured from Ti-17 alloy and micropolished for enhanced fatigue life, machined heat-treated chromoly spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with spring-loaded valve stem wiper system •Seat lbs./installed height; 217 lbs. at 1.789” (0.574” lift), 215 lb. at 1.800” (0.585” lift), 208 lbs. at 1.819” (0.604” lift), 200 lbs. at 1.845” (0.630” lift), 185 lbs. at 1.900” (0.685” lift), 170 lbs. at 1.935” (0.720” lift), 415 lbs. at 1.215” (open height) coil bind at 1.125” •Dyno proven and track tested •Feuling® BeeHive valve springs must be installed at the correct OPEN HEIGHT, matching max lift to the open height spec of the valve springs •Made in the U.S.A. NOTE: Feuling BeeHive valve spring kits are direct replacement with no machining or rocker box clearance required up to 0.574” lift for 99-04 Big Twin and 86-03 XL and up to 0.700” lift for 05-17 Twin Cam. Larger camshafts require valve guide machining for seal-to-retainer clearance. PART # DESCRIPTION FOR 05-17 88”/96”/103” TWIN CAM, 04-22 XL (EXCEPT RH SPORTSTER), 09-12 XR 1200 0926-1468 7°, 7 mm valve stem w/ stock triple keeper groove (includes steel retainers) 0926-3323 7°, 7 mm valve stem w/ stock triple keeper groove (includes titanium retainers) PART # DESCRIPTION FOR 99-04 TWIN CAM AND 86-03 XL 0926-1467 7°, 5/16” valve stem w/ stock keeper groove (includes steel retainers) 0926-3322 7°, 5/16” valve stem w/ stock keeper groove (includes titanium retainers) ECONO BEEHIVE® VALVE SPRING KITS •Made from premium stress-relieved conical ovate wire •Feature extremely high-level of fatigue life •Use a much smaller and lighter weight retainer to reduce valve weight and create quicker rev and smoother motion •Designed to handle the demands of performance engines with 0.585” and smaller lift camshafts •Available for 5/16” and 7 mm valves •PART #s 0926-1467 and 0926-1468 include Econo BeeHive® valve springs, lightweight 7° steel retainers, machined heat-treated chromoly spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with spring-loaded valve stem wiper system •PART #s 0926-3322 and 0926-3323 include Econo BeeHive valve springs, lightweight 7° Ti retainers, machined heat-treated chromoly spring seats, seat shims, valve locks and a set of premium Viton valve seals equipped with spring-loaded valve stem wiper system 0926-3323 0926-1467 0926-1469 •Seat lb./installed height; 183 lbs. at 1.760” (0.510” lift), 175 lbs. at 1.785” (0.535” lift), 172 lbs. at 1.803” (0.553” lift), 165 lbs. at 1.825” (0.574” lift), 163 lbs. at 1.835” (0.585” lift), 380 lbs. at 1.250” OPEN HEIGHT coil bind at 1.180” •Dyno proven and track tested •Feuling® BeeHive® valve springs must be installed at the correct OPEN HEIGHT, matching max lift to the open height spec of the valve springs •Made in the U.S.A. NOTE: Econo BeeHive® kits are direct replacement with no machining or rocker box clearance required for cams up to 0.574” lift for 99-04 Big Twin and 86-03 XL and up to 0.585” lift for 05-17 Twin Cam.
RkJQdWJsaXNoZXIy OTcxOTk3