dragspecialties.com SECTION 7 All part numbers in BLUE are new for 2025. WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 761 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. ROD SETS •Heavy-duty replacements, perfect for stock motors •Meet or exceed OEM specifications •Come completely fitted and ready to install •Complete set includes a two-hole crankpin, aluminum retainers, bearings, nuts and forged heat-treated steel rods NOTE: Check rod beam to flywheel for proper clearance. PART # DESCRIPTION 0923-0689 For 17-24 M-Eight (104”/107”/114”) 0923-0630 For 07-16 FLHT/FLHR/FLHX/FLTR, 07-17 Softail and 07-17 FXD/FXDWG (96”/103”) (tapered small rod ends) 0923-0629 For 99-06 FLHT/FLHR/FLHX/FLTR, 00-04 Softail and 99-06 FXD/FXDWG (88”) (small straight rod ends) 0923-0467 For 05-06 Softail; repl. OEM # 23971-03/03A (tapered small rod ends) DS-194664 For 86-99 XL; repl. OEM #24275-86A HEAVY-DUTY CONNECTING ROD SET •High-quality, heavy-duty rod set comes complete and ready-to-install •Set includes front and rear rods, crankpin and nuts, steel cages and roller bearings •Rods are deep-forged and heat-treated, 0.120” wider than stock in the I-beam section and feature rod-to-rod clearance to accommodate strokes up to and including 5” •Crankpin has two oil holes and rod has four slots ground on each side of the throw ends to help maintain the oil film on thrust faces •Made in the U.S.A. NOTE: Installation of rod sets may require additional clearancing of flywheels and cases. PART # DESCRIPTION DS-194655 For 86-99 XL (0.792” wrist pin) CRANKPIN ASSEMBLY •For use in stock and S&S flywheels •Made in the U.S.A. ROD ROLLER BEARINGS WITH RETAINERS •Includes bearings and bearing retainers CRANKPIN •Each sold individually •Optimal replacements exceed or equal OEM specifications •Made in the U.S.A. ROD BEARING RETAINERS •Replacement roller-type for Harley connecting rods •Quality equal to OEM •Sold in sets of three PART # DESCRIPTION 0921-0164 For 86-99 XL PART # DESCRIPTION 0924-0171 For 86-99 XL; repl. OEM #24354-87A PART # DESCRIPTION DS-194006 For L86-98 XL (three hole); repl. OEM #23960-81 PART # DESCRIPTION DS-194017 For 86 XL; repl. OEM #s 24362-54A, 24364-54A DS-194664 0923-0467
RkJQdWJsaXNoZXIy OTcxOTk3