dragspecialties.com SECTION 5 All part numbers in BLUE are new for 2025. WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 633 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* 2120-1169 For 10-24 OEM sensor wiring harness 3 PLUG KIT O2 SENSOR BYPASS •Allows you to bypass OEM O2 sensors when changing from the stock exhaust •For 2010-2023 OEM sensor wiring harness •Made in the U.S.A. PART # DESCRIPTION 1861-0496 18 x 1.5 mm PART # DESCRIPTION 1861-0562 12 x 1.25 mm O2 SENSOR PLUG •Works with any O2 sensor port fitting •Two sizes available: 18 x 1.5 mm or 12 x 1.25 mm •Sold each •Made in the U.S.A. PART # DESCRIPTION 1861-0784 O2 port bushing adapters O2 PORT BUSHING ADAPTERS •Threaded outer and inner adapters reduce O2 sensor port from 18 mm to 12 mm allowing riders to use our exhaust pipes on select, newer-model motorcycles •Sold in pairs •Made in the U.S.A. PART # DESCRIPTION 1861-0790 18 mm x 1.5 PART # DESCRIPTION 1861-0791 12 mm x 1.25 O2 SENSOR PORT PLUGS •Allow non-sensor H-D models to run newer-style exhaust systems equipped with O2 sensor ports •Simply screw into non-essential sensor ports •Sold in pairs •Made in the U.S.A. PART # DESCRIPTION 1861-0464 18 mm x 1.5 PART # DESCRIPTION 1861-0607 12 mm x 1.25 O2 SENSOR PORT PLUG KITS •Allow select pre-closed-loop H-D models to run newer-style exhaust systems equipped with O2 sensor ports •Include two zinc-plated plugs with sealing washers •Simply screw into nonessential sensor ports PART # DESCRIPTION 1861-1185 O2 port bushing adapter O2 PORT BUSHING ADAPTER •Reduce the O2 port from 18 mm to 12 mm •Sold each PART # DESCRIPTION STRAIGHT 1861-05601, 2 18 x 1.5 mm 1861-0561 12 x 1.25 mm PART # DESCRIPTION 45° ANGLE 1861-06941 18 x 1.5 mm 1861-0695 12 x 1.25 mm 1 Not made in the U.S.A. 2 Stainless steel. O2 WELD-IN SENSOR BUNGS •Used to install O2 sensors in exhaust systems •Weld-in style •Available in 12 x 1.25 mm or 18 x 1.5 mm styles •Available in a standard straight style, or machined at a 45° angle •Sold in pairs •Made in the U.S.A. unless noted PART # DESCRIPTION WELD-IN SENSOR BUNGS 7806-1563 18 mm x 1.5 steel 1861-0831 18 mm x 1.5 stainless steel PART # DESCRIPTION SOCKET PLUGS 7806-1564 18 mm x 1.5 steel 1861-0833 18 mm x 1.5 stainless steel 1861-0832 12 mm x 1.25 steel O2 SENSOR WELD-IN BUNGS AND PLUGS •Allow for easy installation of oxygen sensors •Sold each •Made in the U.S.A. PART # DESCRIPTION 1861-0728 O2 sensor bung, plug and washer kit 1861-0523 Weld-in O2 sensor bung 1861-0522 O2 sensor bung plug 1860-0545 Aluminum washer for O2 sensor plug O2 SENSOR BUNG, PLUG AND WASHER •Available as a set or individually •Weld-in O2 sensor bung allows installation of O2 sensors in most exhaust systems; 18 mm x 1.5 •O2 sensor bung plug works with 18 mm O2 sensor bungs; 18 mm x 1.5 •Aluminum bung plug washer fits any 18 mm O2 sensor bung plug PART # DESCRIPTION 1861-0525 EGT bushing WELD-ON EGT BUNG •Allows installation of exhaust gas temperature meter •Sold each 1861-0496 1861-0790 1861-0464 1861-0607 1861-0728 1861-0831 1861-0832 1861-0560 1861-0694
RkJQdWJsaXNoZXIy OTcxOTk3