dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 10 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 1090 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. TURN SIGNAL RELOCATION/EXTENSION KIT •The perfect solution for relocating your handlebar-mounted turn signals •Allows you to relocate your turn signal lamps without running wires inside your handlebars •Wires are color-coded the same as factory, so moving your turn signals is a breeze PART # DESCRIPTION 2120-0885 For 16-23 models (all) FRONT TURN SIGNAL EXTENSION HARNESSES •Plug-and-play solution for extending the OEM front turn signal wires •Easily allows for relocation of OEM turn signal housings when handlebars are upgraded •Plug-and-play JAE connectors are offered with four different lengths and color matched wire colors FRONT TURN SIGNAL EXTENSION HARNESS KITS •A must when installing taller handlebars •Intended for front turn signals mounted on handlebar switch housings •No crimping necessary •Made in the U.S.A. FRONT TURN SIGNAL RELOCATION HARNESS •36” extensions allow relocation of handlebar switch-mounted turn signals on models with CAN bus electrical systems •After cutting and disconnecting the wires at the switch housings, extensions are soldered in; OEM-style plugs connect into the two 3-position multiblock connectors under the fuel tank that is still installed on CAN bus models but not used with handlebar switch-mounted signals •Made in the U.S.A. FRONT TURN SIGNAL EXTENSIONS •36” extensions allow relocation of handlebar switch-mounted turn signals on models with CAN bus electrical systems •After cutting and disconnecting the wires at the switch housings, extensions are soldered in; OEM-style plugs connect into the 6-position multiblock connector under the fuel tank that is still installed on CAN bus models but not used with handlebar switch-mounted signals •Made in the U.S.A. FRONT ABS EXTENSION HARNESS •Safe and easy method for lengthening your front end and keeping ABS properly connected •12” extension •Plug-and-play installation •Made in the U.S.A. PART # DESCRIPTION 2120-0629 For 11-17 FXST/FLST PART # FITS MODEL 2120-1165 For 08-24 FLHT/FLHX/FLTRX and 08-16 FLHR •Harnesses easily plug in-line with left and right OEM turn signal connections extending the wire length for relocation •Sold as a pair PART # DESCRIPTION FOR 16-24 FLSTF/FLSTFB/F LFB/FLFBS, 16-21 FLSL, 16-17 FLSTFBS/FLSS/FXSE, 18-21 FXSB, 23-24 FXBR, 18-20 FXLR, 20-24 FXLRS, 21-24 FXST, 18-24 FXBB/FXBBS AND 18-23 FXFB/FXFBS 2120-1224 +4” 2120-1225 +8” PART # DESCRIPTION FOR 16-24 FLSTF/FLSTFB/FLFB/FLFBS, 16-21 FLSL, 16-17 FLSTFBS/FLSS/FXSE, 18-21 FXSB, 23-24 FXBR, 18-20 FXLR, 20-24 FXLRS, 21-24 FXST, 18-24 FXBB/FXBBS AND 18-23 FXFB/FXFBS (CONT) 2120-1226 +12” 2120-1227 +15” PART # DESCRIPTION FOR 16-24 SOFTAIL (EXCEPT FLSTC AND FLSTN) 2120-0851 +4” 2120-0852 +8” 2120-0853 +12” 2120-0854 +15” PART # DESCRIPTION FOR 96-15 SOFTAIL, DYNA AND XL 2120-0344 +4” 2120-0345 +8” 2120-0346 +12” 2120-0347 +15” PART # DESCRIPTION 2120-0785 For 12-17 Dyna 2120-1224 2120-1225 2120-1226 2120-1227 2120-0344 2120-0851
RkJQdWJsaXNoZXIy OTcxOTk3