dragspecialties.com All part numbers in BLUE are new for 2025. SECTION 10 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 1028 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION FOR 04-06 CARBURETED TWIN CAM AND XL W/ A SINGLE 12-PIN CONNECTOR 2105-0127 Ignition module and harness kit 2105-0128 Ignition module and harness kit w/ coil and plug wires PART # DESCRIPTION FOR 99-03 CARBURETED TWIN CAM W/ TWO 12-PIN CONNECTORS 2105-0125 Ignition module and harness kit 2105-0126 Ignition module and harness kit w/ coil and plug wires IGNITION MODULE AND WIRE HARNESS KITS •Use this kit for custom bike builds or replacing faulty stock ignition harnesses •The wire harness includes your stock connectors for the coil, map sensor, crank position sensor and diagnostic port, as well as leads for ground, 12V switched connection and tach wire •PART #2105-0127 includes 1009-TC88A ignition module PART #2101-0034; PART #2105-0128 includes 1009-TC88A ignition module PART #2101-0034, coil PART #7805-3031 and plug wires PART #7806-1556 PART # DESCRIPTION STANDARD PLUG-IN IGNITION MODULES 2101-0034 For 04-06 carbureted Twin Cam and XL w/ a single 12-pin connector DS242377 For 99-03 carbureted Twin Cam w/ two 12-pin connectors 2101-02191 For 99-03 carbureted Twin Cam w/ two 12-pin connectors and two-stage rev limiter (race only) 2101-0202 For 04-07 American Iron Horse PART # DESCRIPTION CARB PLUG-IN IGNITION MODULES 2101-02182 For 04-06 carbureted Twin Cam and XL w/ a single 12-pin connector (TC88A EX) 2101-02172 For 99-03 carbureted Twin Cam w/ two 12-pin connectors (TC88 EX) OPTIONAL ACCESSORIES 2101-0075 USB interface 1 Requires USB interface PART #2101-0075 to program. 2 Exempt per CARB Executive Order (E.O.) #D-641-1. PLUG-IN IGNITION MODULES •Features two advance curve families that are adjustable to accommodate stock and modified engines •Selectable multi-spark mode for quick starting and smooth cruising •Four rotary switches for mode select, timing adjustments, advance slope and rpm limit (in 100 rpm steps) •Coil outputs protected against short circuits •Requires OEM coils with less than 1-ohm primary resistance and low-resistance spiral-core or carbon-core suppression-type plug wires •12V power adapters are used to power up the modules when removed from the bike (sold separately) •Optional USB interface PART #2101-0075 and software required for programming custom curves (programs available on website www.daytona-twintec.com/index.html) •Includes easy-to-follow instructions •Made in the U.S.A. NOTE: Will not work on fuel-injected models. •PART #2105-0125 includes 1008-TC88 ignition module PART #DS242377; PART #2105-0126 includes 1008-TC88 ignition module PART #DS242377, coil PART #7805-3031 and plug wires PART #7806-1556 •Made in the U.S.A. 2101-0218 2101-0219 2101-0075 2105-0127 2105-0126
RkJQdWJsaXNoZXIy OTcxOTk3