BOLD MAGENTA part numbers are new for 2025 DRAGSPECIALTIES.COM 2025 | TIRE & SERVICE V-TWIN TOOLS 690 TWIN SCAN DIAGNOSTIC KITS • Communicate with ECM,TSSM and BCM to read, then clear diagnostic trouble codes •Activate ABS solenoids for proper brake bleeding and testing •Real time display of engine sensors along with built in data logging will store data for up to one hour •Data logging automatically triggered when a trouble code is set and shows the data before and after code is set •PART #3807-0445 programs and reads key fobs, programs PIN and disables security • Activate modules, lights, indicators fuel pump drain and electronic throttle sweep; tests different actuators, lights and indicators • Calibrate speedometer, remove new speedometer display of VinErr •Enable or disable settings in the ECM such as ACR (automatic compression release for performing engine compression testing), EITMS, cruise control, and active exhaust, reads and sets engine idle speed rpm • Enable or disable settings in the BCM for ignition switch, new radio installation, bank angle sensor for trike installs, program fog light function,ABS installation, and enable service state WEGO III WIDE-BAND AFR (AIR/FUEL/RATIO) MONITORING TOOLS •Professional air/fuel ratio system with built-in data logging •Versatile tuning aid for carbureted and fuel injection engines; suitable for on-road and dyno tuning •Highly accurate with less than +/- 0.10 AFR error over 10.3-19.5 AFR range using Bosch LSU 4.2 5 wire wide band oxygen sensor(s) •Easy free air calibration procedure corrects for effects created due to sensor aging •0 to 5V analog AFR output for interface to dyno instrumentation; easily interfaced to all leading dyno systems •Waterproof with ultra-bright daylight-readable blue display features automatic dimming function •11 to 16VDC supply voltage needed for operation; current drain is approximately 1 amp •Built-in USB interface PART # DESCRIPTION 3807-0445 Twin Scan 4 for 14-20 Touring, 11-20 Softail, 12-17 Dyna and 14-20 XL w/ CAN data Bus (all models with a 6-pin diagnostics connector) 3807-0206 Twin Scan 2 for 01-13 models including V-Rod and 08-13 Touring w/ 36-pin Delphi fuel-injection system (except 11-13 Softail and 12-13 Dyna) and 03-06 carbureted models w/ 12-pin module 1022-0224 Twin Scan WEGO Upgrade Kit for any Twin Scan II, 3 or 4; includes WEGO IIID Interface, two Bosch LSU 4.2 wide-band oxygen sensors, two 18 x 1.5 mm weld nuts and two 18 x 1.5 mm hex socket plugs PART # DESCRIPTION 1022-0054 Single channel PART # DESCRIPTION 1022-0110 Dual channel •Data logging software needs a PC or laptop with Windows 7/8/10; data can also be exported to an Excel spreadsheet for further analysis • Compact size: 4” L x 2”W x 0.5” H •Include WEGO III Wide Band Exhaust Gas O2 Sensor Interface, 42” harness, Bosch O2 Sensor(s), 18 mm x 1.5 weld nut(s) for sensor mounting and software •Use PART #1022-0008 for replacement Bosch O2 sensor (sold each) •Made in the U.S.A. •Latest software will include the latest firmware for easy remote updating of the Twin Scan 4 •Include two analog inputs with 0-20V or ± 200V range as well as two-channel oscilloscope capability for waveform display •Analog inputs can also be used for air/flow ratio (AFR) •Easy to navigate software • Require use of a PC with Windows 7,Windows 8, Windows 10 or Windows 11 for display •WEGO IIID dual channel wide-band exhaust gas oxygen sensor interface upgrade kit PART #1022-0224 will log engine data along with the actual air/fuel ratio (AFR); logged AFR data can be analyzed and displayed •Use PART #1022-0008 for replacement Bosch O2 sensor; sold each •Made in the U.S.A. NOTE: Models equipped with 12 mm oxygen sensors will require 18 mm weld nuts be installed in the exhaust system for use with the Twin Scan 3+ kit 18 mm oxygen sensors. 3807-0445 3807-0206 1022-0110
RkJQdWJsaXNoZXIy OTcxOTk3