BOLD MAGENTA part numbers are new for 2025 DRAGSPECIALTIES.COM 2025 | TIRE & SERVICE V-TWIN TOOLS 658 SPROCKET SHAFT BEARING RACE TOOL • Used to remove and install Timken® bearing race on motor cases •Uses drivers with handle PART #DS-196042 •Made in the U.S.A. XL SPROCKET NUT SOCKET TOOL •Short socket is specifically designed to remove, install and properly tighten the front final drive sprocket/p ulley •Ensures mainshaft on the XL extends through the guidance collar for correct alignment •Provides full contact to the nut when tightening •Made in the U.S.A. BEARING AND RACE PULLER TOOL •Multi-faceted tool has many uses • Removes flywheel sprocket shaft inner bearing race on 03-07 Twin Cam • Can be used to remove Timken® bearing (OEM #9028 or #9029) on 55-07 Big Twins, including JIMS 120” engines • Can be used to remove Timken bearing pinion shaft inner bearing race on 57-07 XL, including all Buells •Can also be used to remove press-fit transmission gears and bearings from input and output shafts on all 02-07 V-Rod models •Made in the U.S.A. MAIN BEARING REMOVER/INSTALLER •Removes left and right main bearing without damaging case •Provides correct alignment and depth during installation •Made in the U.S.A. STATOR ADAPTER MAIN BEARING TOOL •This adapter is a simple time and money saver when installing JIMS main bearing on a M-Eight left-side crankcase •When this adapter is used in conjunction with the main bearing tool (PART #3801-0322), or the OEM tool, the stator can remain attached to the left side case during bearing installation •The adapter has been designed with added clearance for the stator screw, which are one time use only screws •It will also guarantee that the case plug seal of the statoris not compromised resulting in a leak • Manufactured from quality 1144 steel, plated in black oxide for corrosion resistance •Simply position this adapter on top of the bearing support on the press table •Made in the U.S.A FLYWHEEL PULLER TOOL •Ensures good and solid engagement when using the puller •Eliminates potential damage to the flywheel when used in this application •Made in the U.S.A. CRANKSHAFT BEARING TOOL •Used to remove and install the right crankcase bearing in Twin Cam motors • Allows straight installation, without damage to the case •Includes instructions •Made in the U.S.A. PART # DESCRIPTION BEARING RACE TOOL DS-196046 For 69-02 Big Twin DS-196045 For 77-03 XL, 94-02 Buell PART # DESCRIPTION DRIVER HANDLE DS-196042 Handle/driver only (ea.) PART # DESCRIPTION 3802-0066 For 91-20 XL and Buell (except Buell 1125R) PART # DESCRIPTION 3801-0088 Bearing and race puller tool PART # DESCRIPTION 3801-0322 For 17-20 M-Eight PART # DESCRIPTION 3801-0424 For 17-22 M-Eight PART # DESCRIPTION 3801-0293 For 15-16 Indian Scout PART # DESCRIPTION DS-196194 For 99-02 Twin Cam “A” motors FLYWHEEL SOCKETS •Made of 4130 chromoly steel •Available in 1/2” or 3/4” drive •Machined for 100% nut-to-socket and drive-end contact •Eliminates nut rounding and risk of injury •Made in the U.S.A. PART # DESCRIPTION 1/2” DRIVE DS-196104 For crankpin nut OEM #23969-83; L83-99 Big Twin 11/2” PART # DESCRIPTION 3/4” DRIVE DS-196110 For sprocket shaft nut OEM #24017-80; 72-99 Big Twin 15/8” DS-196110 DS-196104 DS-196046 DS-196042 ENGINE ROTATORS •Rotates flywheel/piston assembly with engine still in frame or on a bench • The perfect tool when doing pushrod adjustments, building big-inch engines and checking operating clearances •Also can be used to keep the flywheel assembly from rotating when torquing the cam drive sprockets retention bolts •Built with a long socket design, making it easier to use without a 1/2” drive extension on your 1/2” driver PART # DESCRIPTION 3801-0099 For all 07-17 Twin Cam, 06 Dyna Glide PART # DESCRIPTION 3801-0100 For 55-06 Big Twin (except 06 Dyna Glide) •Made in the U.S.A. NOTE: Not for use with an air or electric impact wrench; this tool is only guaranteed for use with hand drivers. 3801-0100 3801-0099
RkJQdWJsaXNoZXIy OTcxOTk3