BOLD MAGENTA part numbers are new for 2025 SERVICE & MAINTENANCE TOOLS DRAGSPECIALTIES.COM TIRE & SERVICE | 2025 SERVICE & MAINTENANCE TOOLS 587 DESCRIPTION PART # Damper rod fork tool MP08-117 DAMPER ROD FORK TOOL •Aids in assembly and disassembly of most 41, 43, 46 and 47 mm Kayaba and Showa inverted forks •Is used in applications where the manufacturer recommends the following tools: Honda; OEM tool #07PMB-KZ4010A/ Yamaha; OEM tool #YM-01423 •Not required on Honda CR 91-92 models •Hardened steel with black finish DESCRIPTION PART # Fork compression valve removal tool 3805-0022 FORK COMPRESSION VALVE REMOVAL TOOL • For Honda CRF250R 10-12, CRF450R 09-12, Kawasaki KX250F 11-13, KX450F 09-12, Yamaha YZ125/250 05-18,YZ250F/450F 06-18,YZ250FX 06-18 and YZ450FX 16-18 •For removing the compression valve from the fork cartridge •19 mm drive hex; 36 mm octagon •Manufactured from billet 6061-T6 aluminum •Replaces Honda OEM #070MB-MENA100 and Yamaha OEM #YM-01500 DESCRIPTION PART # Hex tool for Showa SFF forks 3805-0125 AIR FORK HEX TOOL FOR SHOWA SFF FORKS •Removes the 22 mm lower sealing bolt from Showa SFF Air Fork •Nonmarking 6061 billet aluminum construction •Anodized finish •Made in the U.S.A. DESCRIPTION PART # Shaft clamp 3805-0218 SHAFT CLAMP •Makes replacing shaft eyelets easier •Holds 0.5”/12 mm through 0.875”/22 mm without causing damage to the shaft •Includes bolts for use without a vice DESCRIPTION PART # Shock metering pin tool 3805-0069 SHOCK METERING PIN TOOL FOR 09-16 KTM MODELS WITH WP PDS SHOCKS •Shock metering pin removal tool for WP PDS shocks •T-handle tool that’s incredibly easy to maneuver with a long reach for disassembly and servicing •Shaft features two locator washers that allow the tool to rest inside the shock body and not get skewed while tightening or loosening the compression metering pin SIZE USE PART # 10 mm, 12 mm, 12.5 mm, 14 mm Damping rods TFSH-10 14 mm, 16 mm, 18 mm Shock shafts TFSH14 20 mm, 24 mm, 29 mm 20 mm and 25 mm fork cartridges TFSH-20 32 mm, 35 mm 32 mm fork cartridges TFSH-32 SHAFT HOLDING TOOLS •A must for all suspension work • For a firm grip on shock shafts, fork cartridges, damping rods or other round shafts while servicing • Tough, aluminum construction DESCRIPTION PART # Fork seal bullet set 3805-0193 39 mm bullet MP08-0273 43 mm bullet MP08-0275 45 mm bullet MP08-0276 DESCRIPTION PART # 46 mm bullet MP08-0277 47 mm bullet MP08-0278 48 mm bullet 3805-0001 49 mm bullet 3805-0171 FORK SEAL BULLET TOOL SET •Protect the fork seal and wiper of inverted forks from damage by the bushing groove during installation •Save time by eliminating the need to wrap the fork tube with tape • Set includes 36, 41, 43, 45, 46, 47, 48 and 49 mm bullet tools; also available separately •Fitment size is marked on each bullet for easy identification DESCRIPTION PART # Rebound piston ring compressor 3805-0049 REBOUND PISTON RING COMPRESSOR FOR KTM •Required for assembly of newer WP Dual Chamber forks •Compresses rebound piston ring to allow insertion into the cartridge tube TFSH14 3805-0193
RkJQdWJsaXNoZXIy OTcxOTk3