BOLD MAGENTA part numbers are new for 2024 PARTS-UNLIMITED.COM 2024 | ATV/UTV FUEL/AIR SYSTEMS 1300 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. IN-LINE FUEL VALVES •For use with auxiliary fuel tank or other use requiring an in-line installation •Features double neoprene seals and O-rings •Smooth and positive operation •PART #P537 is not recommended for engines over 200cc •PART #s P12-035 and P12-036 are not recommended for engines over 300cc DESCRIPTION PART # SUG. RETAIL For 3/16” fuel line P537 $12.95 DESCRIPTION PART # SUG. RETAIL For 1/4” fuel line P12-035 $19.95 DESCRIPTION PART # SUG. RETAIL For 5/16” fuel line P12-036 $19.95 P537 P12-035 P12-036 FUEL LINE QUICK-DISCONNECT COUPLINGS •Single or dual shut-off valves •When connected fuel will flow and when disconnected fuel will not flow •Use dual shut-off for fuel tanks equipped with a crossover line • For fuel supply (fuel tank to carburetor), use the original quick-disconnect couplings with the single shut-off valve •Available for 1/4” and 5/16” ID fuel line •Capable of withstanding temperatures of -40°F to 180°F • These quick-disconnect fittings utilize Viton®-type fluoroelastomer O-rings with superior chemical resistance •Made in the U.S.A. NOTE: Not for use with fuel injected engines. DESCRIPTION PART # SUG. RETAIL Single, 1/4” P12-029 $32.95 Single, 5/16” P12-030 32.95 DESCRIPTION PART # SUG. RETAIL Dual, 1/4” P12-037 $44.95 Dual, 5/16” P12-038 49.95 P12-030 P12-029 P12-037 P12-038 STRAIGHT-THROUGH FUEL LINE QUICK-DISCONNECT COUPLINGS •Straight through; no shut off •Available for 1/4” and 5/16” ID fuel line •Capable of withstanding temperatures of -40°F-180°F SIZE PART # SUG. RETAIL 1/4” ID 0706-0035 $18.95 SIZE PART # SUG. RETAIL 5/16” ID 0706-0034 $23.95 0706-0034 STEPLESS® EAR CLAMP KIT FOR FUEL SYSTEM •Convenient kit includes 80 pieces of hardware, a Motion Pro Side Jaw Pincher tool and a convenient fuel line clamp size chart •Narrow 5mm wide band provides concentrated seal compression •360° Stepless® design with no gaps on inner surface •Specially formed strip edges reduce the risk of damage to the part being clamped DESCRIPTION PART # SUG. RETAIL Fuel system stepless clamp kit 2402-0132 $184.95 Stepless clamps, 7.8-9.5mm (fit Motion Pro Premium and clear vinyl 3/16” ID fuel line) (10-pk.) 2401-0557 11.95 Stepless clamps, 8.8-10.5mm (fit Motion Pro Low Permeation yellow fuel line w/ 1/4” ID) (10-pk.) 2401-0819 11.95 Stepless clamps, 9.6-11.13mm (fit Motion Pro Premium and clear vinyl 3/16” ID fuel line) (10-pk.) 2401-0716 11.95 Stepless clamps, 10.3-12.8mm (fit Motion Pro Premium 1/4” ID fuel line) (10-pk.) 2401-0558 11.95 Stepless clamps, 10.8-13.3mm (fit Motion Pro clear vinyl1/4” ID fuel line) (10-pk.) 2401-0559 11.95 Stepless clamps, 12.0-14.5mm (fit Motion Pro Premium and clear vinyl 5/16” ID fuel line) (10-pk.) 2401-0560 11.95 Stepless clamps, 13.2-15.7mm (10-pk.) 2401-0717 12.95 Stepless clamps, 14.8-18.0mm (fit Motion Pro Premium and clear vinyl 3/8” ID fuel line) (10-pk.) 2401-0561 13.95 •Lightweight design •Tampering is visible •Kit includes 10 each of the clamps listed below in a convenient storage box •Individual clamp sizes available separately in 10-pack for restocking •Side jaw clamp pincher tool PART #3801-0182 also available separately FUEL LINE FITTINGS • T- and Y- connectors made from white fuel-resistant plastic (Acetal) •Fitting used to run two hoses into one •May be used with O-clips or hose clamps •Double-ear O-clips are easy to install DESCRIPTION PART # SUG. RETAIL 3/16” Y-connectors P12-014 $42.95 3/16” T-connectors P12-018 48.95 1/4” Y-connectors P12-015 45.95 1/4” T-connectors P12-019 48.95 DESCRIPTION PART # SUG. RETAIL 5/16” Y-connectors P12-016 $65.95 5/16” T-connectors P12-020 48.95 3/8” T-connectors P12-021 77.95 5/16” O-clips for 3/16” hose 2401-0390 12.95 •For use in low-pressure applications • Snag-free, smooth, polished finish • Strong, positive clamping strength without damage to the hose •Simple to remove by clipping an ear •Connectors and O-clips sold in packs of 10 •Viton®-type fluoroelastomer O-rings provide superior chemical resistance •Made in the U.S.A. NOTE: Not for use with fuel injected engines. 2402-0132 2401-0559 DESCRIPTION PART # SUG. RETAIL 7/16” O-clips for 1/4” hose 2401-0095 $12.95 1/2” O-clips for 5/16” hose 2401-0096 12.95 9/16” O-clips for 3/8” hose 2401-0391 12.95
RkJQdWJsaXNoZXIy OTcxOTk3