dragspecialties.com SECTION 7 All part numbers in BLUE are new for 2024. WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 841 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. CLARITY CAM COVERS •Allows for viewing of the internal moving engine components •CNC-machined from billet aluminum •PART #s 0940-1128, 0940-1129, 0940-1130 have a thinner design with smaller windows for additional exhaust clearance; will fit 02-16 Twin Cam models where this is needed •Hardware included •Contrast Cut starts with a polished surface that is black anodized then re-cut to open the design •Black Ops features a gloss-black finish over a contrasting texture black finish for outstanding durability and looks •Matching Clarity air cleaner and derby cover available •Made in the U.S.A. The RSD Clarity Cam Covers contain two pre-installed Lexan® polycarbonate windows. These windows are very resistant to almost everything a motorcycle will be exposed to. However, extra care and preparation must be taken when installing the cam cover near the exhaust system. The Lexan® polycarbonate windows must be at least 5/16” away from the exhaust pipe to ensure the temperature does not exceed the capabilities of the Lexan®. Additional clearance is recommended to preserve the optical clarity of the Lexan® window as well as reducing the amount of heat introduced to the engine from the exhaust. Take measurements when installing the exhaust system and make sure that the exhaust NEVER contacts the Lexan® windows, bolts or the aluminum cam cover. Lexan® is very durable but it must be treated just like any plastic and cannot come into contact with the exhaust pipes. The Lexan® windows, just like any plastic, will melt if in direct contact with the exhaust pipe. If the Lexan® windows have less than adequate clearance, premature discoloration, cracking or melting may occur causing severe failure and/or possible injury to the rider. RSD recommends the use of “high pipes” or exhaust that runs above the cam cover, which eliminates any potential exhaust contact. TECHNICAL GUIDELINES FOR CLARITY CAM COVER: 1. There must be at least 5/16” between the exhaust and the Lexan® windows, bolts and cover. 2. Absolutely no contact between the Lexan® windows, bolts or aluminum cam cover. 3. Do not use brake cleaner, acetone or any harsh chemicals during installation. 4. Use Plexus cleaner for cleaning. If any other cleaners are used, read the label to verify compatibility with Lexan®. 0940-1729 0940-1128 0940-1129 0940-1057 0940-1058 PART # DESCRIPTION SUG. RETAIL FOR 17-23 M-EIGHT MODELS 0940-1729 Contrast Cut™ $494.95 0940-1731 Black Ops™ 494.95 FOR 02-16 FLHT/FLHR/FLHX/FLTR MODELS 0940-1128 Chrome 471.95 0940-1129 Contrast Cut™ 459.95 0940-1130 Black Ops™ 459.95 PART # DESCRIPTION SUG. RETAIL FOR 01-17 TWIN CAM MODELS W/O CAM POSITION SENSOR (EXCEPT 01-08 FL TOURING MODELS) 0940-1056 Chrome $494.95 0940-1057 Contrast Cut™ 494.95 0940-1058 Black Ops™ 494.95
RkJQdWJsaXNoZXIy OTcxOTk3