dragspecialties.com All part numbers in BLUE are new for 2024. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 778 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION SUG. RETAIL DS194328 HIGH ENERGY™ for 17-23 M-Eight, 99-17 Twin Cam, 00-22 XL/XR1200 (except RH Sportster models) and 00-09 Buell models $27.95 DS194329 HIGH ENERGY™ for 17-23 M-Eight, 99-17 Twin Cam, 00-22 XL/XR1200 (except RH Sportster models) and 00-09 Buell models 29.95 DS-1942621 HY-REV™ for 91-99 XL and 94-99 Buell 31.95 1 Requires adjustable pushrods. V-THUNDER™ TAPPET ASSEMBLIES •Features an oil metering design that provides uniform metering throughout the entire rpm range •Rollers and axles are manufactured from high-carbon/chromium bearing-quality steel, which is through-hardened for improved wear and load-carrying capability, and the pushrod seat is carbo-nitrided •Each unit is 100% tested for proper function •HIGH ENERGY™ hydraulic roller lifter is a performance replacement for the stock hydraulic roller lifter, which should be used for street applications • PRO-MAGNUM™ hydraulic roller lifter is designed to perform at higher engine speeds, as in race applications, and a slight increase in noise should be expected; unique anti-pump-up retainer is designed to replace the stock spring retainer clip, which precisely limits plunger travel •HY-REV™ hydraulic roller lifter features internal hydraulic check valve, which allows for higher rpm •Sold each •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 86-90 XL 0929-0078 Race forged tappet (ea.) $106.95 0929-0079 Race forged tappets (set of 4) 418.95 V-THUNDER™ RACE FORGED TAPPETS •Forged design is stronger than commonly available cast or billet designs •Race/slow bleed upgrade design for high-performance use •Each unit is 100% tested for proper function •Black oxide finish •Available individually or in a set of four •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 86-90 XL MODELS 0929-0076 Performance forged tappet (ea.) $82.95 0929-0077 Performance forged tappets (set of 4) 326.95 V-THUNDER™ PERFORMANCE FORGED TAPPETS •Forged design is stronger than commonly available cast or billet designs •Performance replacement for the stock hydraulic roller lifter •Each unit is 100% tested for proper function •Black oxide finish •Available individually or in a set of four •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-21 XL (EXCEPT RH SPORTSTER), 09-12 XR 1200 AND 00-09 BUELL MODELS 0929-0046 Standard $179.95 PART # DESCRIPTION SUG. RETAIL FOR 86-90 XL AND 87-90 BUELL MODELS 0929-0043 Standard $141.95 0929-0044 +.002” oversize 145.95 POWERGLIDE™ STEADY ROLL TAPPETS •The same Powerglide advantage (oil-fed axle, billet steel body, precision fit hydraulics) but now incorporates a Steady Roll bronze bushing in place of the needle bearing roller •These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities •Billet body •Increased roller width •Roller perpendicularity held to .0002” 0929-0043 0929-0046 PART # EMIS* DESCRIPTION SUG. RETAIL FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-21 XL/XR 1200 (EXCEPT RH SPORTSTER) AND 00-09 BUELL MODELS 0929-0014 3* Standard $179.95 PART # EMIS* DESCRIPTION SUG. RETAIL FOR 17-21 M-EIGHT, 99-17 TWIN CAM, 00-21 XL/XR 1200 (EXCEPT RH SPORTSTER) AND 00-09 BUELL MODELS (CONT) 0929-0023 3 +.005” oversize $185.95 POWERGLIDE II HYDRAULIC TAPPETS •These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities •Billet body •Increased roller width •Roller perpendicularity held to .0002” •Hand-honed hydraulic unit cavity •Dynamic load capacities increased over 30% •Lubrication capacities for hydraulic unit and valve train (top end) increased 10% •Hand-honed hydraulic unit cavity •Dynamic load capacities increased over 30% •Lubrication capacities for hydraulic unit and valve train (top end) increased 10% •Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling •Sold each •Made in the U.S.A. •Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling •Sold each •Made in the U.S.A. 0929-0014 DS-194262 0929-0078 0929-0076
RkJQdWJsaXNoZXIy OTcxOTk3