dragspecialties.com SECTION 7 All part numbers in BLUE are new for 2024. WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 773 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION SUG. RETAIL FOR 99-17 TWIN CAM 0928-0105 Quick-install pushrods $219.95 PART # DESCRIPTION SUG. RETAIL FOR 99-17 TWIN CAM (CONT) 0928-0120 7/16”-20 repl. nut for PART #0928-0105 (ea.) $5.95 QUICK-INSTALL PUSHRODS •Strongest Quick-Install pushrod on the market •Strength and rigidity of Quick-Install pushrods are second only to heavy-duty one-piece pushrods •Tube material starts out as 7/16” rod OD, then gets turned down to 3/8” OD leaving heavy duty 7/16”-20 threads for the base and jam nut •Jam nut slides up the pushrod •.134” wall thickness •Base then loosens up into the pushrod to allow Quick-Install access •Individual length exhaust and intake pushrods •Install without the removal of rocker covers •Sold as a set of four •Made in the U.S.A. NOTE: Correct pushrod/lifter adjustment requires starting with fully pumped up lifters. NOTE: Requires Pushrod Tube kit PART #0928-0104 to install; sold separately. PART # DESCRIPTION SUG. RETAIL FOR 99-17 TWIN CAM 0928-0106 Quick-install pushrods/tube kit $279.95 PART # DESCRIPTION SUG. RETAIL FOR 99-17 TWIN CAM (CONT) 0928-0120 7/16”-20 repl. nut for PART #0928-0106 (ea.) $5.95 QUICK-INSTALL PUSHRODS/TUBE KIT •Strongest Quick-Install pushrod on the market •Strength and rigidity of Quick-Install pushrods are second only to heavy-duty one-piece pushrods •Tube material starts out as 7/16” rod OD, then gets turned down to 3/8” OD leaving heavy duty 7/16”-20 threads for the base and jam nut •.134” wall thickness •Jam nut slides up the pushrod •Base then loosens up into the pushrod to allow Quick-Install access •Individual length exhaust and intake pushrods •Install without the removal of rocker covers •Also included in the kit are four chrome lower tubes and clips; use in conjunction with factory inner tubes, covers, caps, springs and washers •Made in the U.S.A. NOTE: Correct pushrod/lifter adjustment requires starting with fully pumped up lifters. NOTE: Quick-Install pushrods have 7/16”-20 threads per inch. .050” adjustment per turn. Two turns = .100”. PART # DESCRIPTION SUG. RETAIL 0928-0040 For 91-03 XL models $149.95 HP+® FIXED-LENGTH PUSHRODS •Maintain maximum valve lift in your Harley Davidson® XL engine •Increased stiffness and column rigidity maximizing valve-train stability, increasing engine rpm horsepower and torque output •3/8” diameter/.065” wall 4130 chromoly fixed-length one-piece pushrods with hardened ball ends •Length is 0.040” under stock, intake 10.706”, exhaust +10.760” •Designed to exceed the needs of performance engines using larger lift camshafts and high spring pressures, while maintaining proper and critical oil flow to top end valve train •Designed for use with hydraulic or solid lifters and street or race engines •These pushrods require removal of rocker covers and rocker arm supports •Made in the U.S.A. 0928-0120 0928-0106 0928-0105 NOTE: Quick-Install pushrods have 7/16”-20 threads per inch. .050” adjustment per turn. Two turns = .100”.
RkJQdWJsaXNoZXIy OTcxOTk3