dragspecialties.com All part numbers in BLUE are new for 2024. SECTION 7 WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 764 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION SUG. RETAIL FOR 17-22 M-EIGHT MODELS 0926-3416 .675” lift (seat pressure 86 lb.) (titanium spring retainers) $661.95 0926-3417 .675” lift (seat pressure 86 lb.) (steel spring retainers) 546.95 0926-3420 .630” lift (seat pressure 101 lb.) (titanium spring retainers) 634.95 0926-3421 .630” lift (seat pressure 317 lb.) (steel spring retainers) 528.95 VALVE SHIM CONVERSION KIT WITH RACING VALVE SPRINGS •Conversion kit uses Kibblewhite racing springs combined with a lightweight valve spring retainer that houses a standard 9.5mm hardened steel shim •Rocker arm rides directly on the 9.5mm shim surface, allowing for a significantly greater rocker arm swipe surface area •Increased rocker arm surface contact area allows the ability to run higher lift cams than previously could not be used with valves having a 6mm valve stem •Rocker shim thickness can be varied by changing shim size to adjust the effect valve stem protrusion height •Increase in valve stem protrusion height with this kit is approximately 0.100” •Feature interference-wound, double-chrome silicone springs •Made in the U.S.A. NOTE: To maximize shim contact in the retainer, Kibblewhite strongly recommends tipping (shortening the valve tip). NOTE: Kibblewhite strongly recommends the use of titanium valves with these kits. PART # DESCRIPTION SUG. RETAIL FOR 17-22 M-EIGHT MODELS 0926-3418 .625” lift (seat pressure 85 lb.) (titanium retainers) $519.95 0926-3419 .625” lift (seat pressure 85 lb.) (steel retainers) 471.95 VALVE SHIM CONVERSION KIT WITH BEEHIVE VALVE SPRINGS •Conversion kit uses Kibblewhite beehive springs combined with a lightweight valve spring retainer that houses a standard 9.5mm hardened steel shim •Rocker arm rides directly on the 9.5mm shim surface, allowing for a significantly greater rocker arm swipe surface area •Increased rocker arm surface contact area allows the ability to run higher lift cams than previously could not be used with valves having a 6mm valve stem •Rocker shim thickness can be varied by changing shim size to adjust the effect valve stem protrusion height •Increase in valve stem protrusion height with this kit is approximately 0.100” •Progressively wound springs using Kobe super-clean, chrome silicon-based wire that is heat-treated and shot peened •Made in the U.S.A. NOTE: To maximize shim contact in the retainer, Kibblewhite strongly recommends tipping (shortening the valve tip). NOTE: Kibblewhite strongly recommends the use of titanium valves with these kits. 0926-3416 0926-3420 0926-3418
RkJQdWJsaXNoZXIy OTcxOTk3