WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com SECTION 5 All part numbers in BLUE are new for the OldBook. 329 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION SUG. RETAIL 3850-0481 Dealer service kit for S&S exhaust $50.95 EXHAUST DEALER SERVICE KIT •Everything needed to perform a required exhaust system service or end cap replacement •Kit includes tamper-proof screws and S&S proprietary tamper-proof screw bit PART # DESCRIPTION 1860-0547 Dog bone kit DOG BONE KIT •Includes two “Dog Bone” nut plates and four 5/16”-18 x 5/8” bolts •Fits all Vance & Hines systems and slip-on mufflers that use the dog bone-style attachment system •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0930-0059 For 48-65 Panhead $11.95 EXHAUST SPIGOT •Designed and machined from 6061-T6 aluminum extruded tubing •Allows you to rebuild the exhaust attachment point on your classic Panhead engine •Welding required •Sold each •Made in the U.S.A. PART # DESCRIPTION EMIS* SUG. RETAIL 1861-0400 Torque cones 3 $42.95 1861-0770 Vortex torque cones 3 70.95 TORQUE CONES •High-temperature stainless steel cones have fully radiused edges for improved engine response, especially low-end torque •Generate correct levels of backpressure for increased horsepower •Fit most stock and aftermarket exhaust systems; fit 13/4”-2” ID exhaust pipes •New Vortex design increases back pressure, improving torque and horsepower •Smooths out the power curve for more consistent performance •Sold in pairs •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1861-0806 Sound reduction kit $39.10 SOUND REDUCTION KIT •Easy, bolt-in sound reduction for 3” HP-Plus® mufflers •Takes off 4dB at idle and improves low-end torque – minimal loss of top-end horsepower •The machined discs with tapered bosses fit into each end of the patented resonator near the exit end of the mufflers and are retained by the supplied bolts and nuts •This kit is designed to use with three-ball style resonators that are 6.50” long •Will also fit most other mufflers (four-ball style resonators) if 1/4”-20 x 11.00” threaded rods are substituted for the supplied bolts •Installation requires removal of the mufflers •Kit includes machined discs and two 7.50” 1/4”-20 bolts and two prevailing torque nuts •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1861-0739 For 1 3/4” OD pipes; 8” L $13.95 1861-1190 For 2” OD pipes; 6” L 13.95 1861-0913 For 2” OD pipes; 9 3/4” L 13.95 1861-0914 For 2 1/4” OD pipes; 8 1/4” L 13.95 1861-0915 For 2 1/2” OD pipes; 8 1/2” L 16.95 1861-0916 For 3” OD pipes; 8” L 16.95 EXHAUST BAFFLES •Fiberglass-wrapped steel construction •Available for a variety of pipe sizes •May require drilling a hole in the exhaust pipe •Sold each PART # DESCRIPTION SUG. RETAIL DS-202019 Repl. baffle for 1 3/4” drag pipes $10.95 REPLACEMENT BAFFLE FOR DRAG SPECIALTIES EXHAUSTS •Steel baffle for 13/4” drag pipes •Sold each PART # DESCRIPTION SUG. RETAIL DS-202011 1 3/4” (ea.) $52.95 DS-202012 1 3/4” (pr.) 98.95 PART # DESCRIPTION SUG. RETAIL DS-202032 2” (pr.) $98.95 HP-PLUS® DRAG PIPE BAFFLES •Dampen sound without impeding flow-through performance •All steel construction; baffles feature HP-Plus® design •Install easily on 13/4” or 2”, 16- or 18-gauge drag pipes •Baffles held by 1/4”-20 screws and locking nuts •Made in the U.S.A. 1861-0400 1861-0770 DS-202012 1861-0739
RkJQdWJsaXNoZXIy OTcxOTk3