2022 Drag Specialties FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com SECTION 7 All part numbers in BLUE are new for 2022. 735 See OLDBOOK For Early Model Applications DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGES 5-6 FOR IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE. PART # DESCRIPTION SUG. RETAIL 0929-0024 For 17-21 M-Eight, 99-17 Twin Cam, 00-21 XL/XR 1200 (except 21 Sportster S/​RH1250S), 00-09 Buell $269.95 RACE SERIES ® SOLID LIFTERS • Designed for engines with radical valve spring pressures and large lift camshafts; maintain proper and critical oil flow to top end with metered oiling • Optimize valvetrain stability, increase engine rpm, horsepower and torque output • Decrease valve float; maintain maximum valve lift • Made from hardened steel, CNC-machined and precision-ground • Utilize standard pushrod seat height; Feuling recommends the use of PART #0928-0010 Race Series ® adjustable pushrods (sold separately; see page 731) PART # DESCRIPTION SUG. RETAIL FOR 17-21 M-EIGHT 0929-0081 Standard $289.95 0929-0082 + .843 - .8435” oversize 289.95 0929-0083 + .8435 - .844” oversize 289.95 FOR 99-17 TWIN CAM, 00-21 XL/XR 1200 (EXCEPT 21 SPORTSTER S/RH 1250S), 00-09 BUELL 0928-0107 Standard 289.95 0928-0108 + .843 - .8435” oversize 289.95 0928-0109 + .8435 - .844” oversize 289.95 RACE SERIES ® SHORT-TRAVEL HYDRAULIC LIFTERS • New revolutionary design with .115” of total travel vs. a full travel lifter with .200” • These lifters will increase rpm by decreasing valve float and valve-train harmonics while maintaining a quiet engine • Travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration in the lifter on steep, fast action high lift camshaft lobes • Short-travel lifters should be set with .065” - .070” of pre-load and with the normal engine growth from heat will put the operating lifter pre-load at or around half travel • Short-travel lifters are designed to limit the amount of oil needed to fill the internals of the lifter which results in less oil needed compared to a full travel or other style short travel lifters • Design drastically reduces aeration of the oil producing a fully filled lifter when the lifter rolls around to the front cam lobe ramp vs. having aerated oil and then the pushrod seat dropping when the lifter hits the front cam ramp after squeezing the aeration • Machined from a steel body and designed to exceed the needs of large lift camshafts and higher valve spring pressures with a slower bleed down rate • Precision ground needle roller bearing with high chromium steel axle for long life and minimal friction • Cold forged extra long piston, precision ground and fitted for controlled leak down and pump up • High-flow disc style quick reacting check valve for better reaction at higher rpm • Race Series ® lifters maintain proper oil flow to the top end, increase engine rpm, valve-train stability, decreasing valve float promoting maximum valve lift • Feuling ® recommends Race Series ® lifters for engines running higher than 185 lb. valve spring seat pressure • Feuling ® recommends the use of a high volume oil pump which will result in quieter, better performing lifters • Race Series ® lifters are compatible with either Feuling ® HP+ ® or Race Series ® oil pumps and are designed for use with both street and strip engines • Spin-Tron dyno developed and track proven • Available in standard and oversized diameters • Sold as a set of four • Made in the U.S.A. NOTE: Feuling ® recommends pumping up each lifter by hand prior to installation, to remove all air and provide a fully pumped up lifter. • Recommended for both strip and high-performance street engines • Sold in a set of four • Made in the U.S.A. NOTE: High volume oil pump recommended. NOTE: Requires removal of rocker covers and rocker arm supports for installation. PART # DESCRIPTION SUG. RETAIL FOR 17-21 M-EIGHT 0929-0072 1 Standard .842” - .8422” $289.95 0929-0073 1 +.8432”-.8435” oversize 289.95 0929-0074 1 +.8437”-.844” oversize 289.95 FOR 99-17 TWIN CAM, 00-21 XL/XR 1200 (EXCEPT 21 SPORTSTER S/RH 1250S), 00-09 BUELL 0929-0007 Standard 289.95 PART # DESCRIPTION SUG. RETAIL FOR 99-17 TWIN CAM, 00-21 XL/XR 1200 (EXCEPT 21 SPORTSTER S/RH 1250S), 00-09 BUELL (CONT) 0929-0008 +.001” $289.95 0929-0009 +.0015” 289.95 FOR 86-90 XL 0929-0022 Standard 289.95 1 Must check clearance on front exhaust lifter to camshaft flange fit. RACE SERIES ® FULL-TRAVEL HYDRAULIC LIFTERS • Full-travel hydraulic lifters made from machined steel designed with .200” of travel • Exceed the needs of large-lift camshafts and higher spring pressures with a slower bleed-down rate • Maintain proper and critical oil flow to valves, springs, rockers, shafts and valve guides • Increase engine rpm and valvetrain stability; decreases valve float for maximum valve lift 0929-0024 0928-0107 • Available in oversize diameters • Recommended for both strip and performance street engines • Sold in a set of four • Made in the U.S.A. NOTE: High-volume oil pump recommended. NOTE: Recommended for engines running higher than 185 lb. valve spring seat pressure. PART # DESCRIPTION SUG. RETAIL 0929-0005 For 17-21 M-Eight, 99-17 Twin Cam, 00-21 XL/XR 1200 (except 21 Sportster S/​RH1250S) and 00-09 Buell $179.95 0929-0017 For 91-99 XL and 94-99 Buell 169.95 0929-0018 For 86-90 XL 239.95 HP+ ® HYDRAULIC LIFTERS • Performance hydraulic roller lifters dyno developed and track tested • CNC-machined and precision ground • When used with Feuling ® oil pump, they will increase critical oil flow to valves, springs, rockers, shafts and valve guides • Extend life of top end valve train • Can also be used for OEM replacements • Sold in a set of four • Made in the U.S.A. NOTE: Requires removal of rocker covers and rocker arm supports for installation when using One Piece pushrods. 0929-0018 0929-0005 0929-0007 0929-0072 0929-0022